主要特點Main features:

Open type vertical heating furnace,tube and flange can pivot and move away from chamber.

開啟式立式加熱體，爐管法蘭可繞軸旋轉移出爐腔。

With standard configuration of OD100mm quartz tube and 40T electrical press

標配Φ100mm石英管真空密封，40T電動壓力機。

Adopt graphite push rod and mould,at the same time of pressing,heat the powder to common sintering temperature or lower,to get the dender and uniform product after a short time

采用石墨頂桿和石墨模具，在加壓的同時使粉末加熱到正常燒結溫度或更低一些，經過較短時間燒結成致密而均勻的制品。

技術參數Technical Parameters

Power

輸入電源

Power rated: 3KW

額定功率：3KW

Voltage

電壓

Voltage rated:  AC220V 50/60HZ

額定電壓： AC220V 50/60HZ

Working Temperature

工作溫度

Max. Temperature: 1200℃ ( 1 hr)

最高溫度：1200℃ (1小時)

Continuous working temperature: ≤1150℃

持續工作溫度：≤1150℃

Max. heating Rate: ≤10℃/min

最快升溫速率：≤10℃/分

Temperature Controller

控溫方式

PID automatic control and auto-tune function.

模糊PID控制和自整定調節

30 programmable segments for precise thermal processing.

智能化30段可編程控制

Built-in protection for the over-heated and broken thermocouple. 

超溫和斷偶報警功能

Heating Elements

加熱元件

Resistance wire, Fe-Cr-Al Alloy doped by Mo

電阻絲（摻鉬鐵鉻鋁合金）

Temperature Accuracy

控溫精度

+/- 1℃

Prosessing tube

爐管

Φ100*460mm

Graphite rod diameter

石墨壓桿直徑

87mm

Pressure maintain time

保壓時間

0-50min

Movable distance

壓力行程

50mm

Plunger diameter

活塞直徑

87mm

Pressure stability

壓力穩定性

≤1MPa/5min

Weight

重量

400kg

Vacuum Flange

真空法蘭

Special designed flanges

定制法蘭 

Vacuum Pressure

真空壓力

1pa can be achieved by mechanical pump

機械泵可達1pa

10^-4 pa can be reached by molecular pump

分子泵可達10^-4pa

Please click the picture below to order vacuum parts

點擊下列圖片訂購真空部件  

Warranty

質保

One year limited warranty with lifetime support (Such consumable parts as tO-rings, etc. are NOT supported by the warranty)

一年質保終身支持（消耗品如O型圈等不在質保范圍內）

Warning

注意事項

Graphite must used under anaerobic condition

石墨必須絕氧使用

Considering contact area calculate pressure

計算壓強時應考慮接觸面積

Small cracks may appear on the surface of the refractory ceramics over extended use. This is a normal occurrence and the cracks may be repaired with alumina coating.

在使用過程中爐膛表面可能出現細小裂紋。這是正常情況，裂紋可以用氧化鋁涂層修復。

Compliance

認證

CE Certified

CE認證

The furnace is ready to pass TUV (UL61010) or CSA certification at extra cost.

可付費進行TUV(UL61010)或CSA認證